A general-purpose cement suitable for all uses for which the special properties of other types of portland cements are not required.
This cement is suggested for use in mortars for exterior, above-grade non-load-bearing walls and interior non-load-bearing partitions.
This product is a commercial grade blend of stone or gravel, sand and cement specially designed for higher early strength. It is ideal for cold weather application, and achieves 5000 psi after 28 days.
This product is a rapid hardening structural concrete. A special blend of cement with specifically graded fine & coarse aggregates, it sets in 20-30 minutes allowing time for mixing, pouring and finishing. Use at any thickness from 1 1/2″ (3.8 cm) to 24″ (61 cm).
Use for setting deck, fence, lamp and mailbox posts; sets posts without mixing – pour dry mix into hole and soak with water. This is a special blend of fast-setting cements, sand and gravel designed to set hard in approx. 20 to 40 minutes.
This product is a high strength Commercial Grade dry pre-blended mixture of sand and cements specially selected for masonry applications. Meets N, S, M requirements as specified in ASTM C270. Just add water.
This product is specially formulated to set in approximately 10-15 minutes. It can be molded or sculpted into place and can be used for making concrete repairs where rapid setting is required. It is ideal for repairing broken edges of concrete steps and curbs.
This product is a rapid setting, high strength repair material designed to plug leaks instantly in concrete and masonry. It sets in 3-5 minutes and can be used above and below grade. It is designed to block running water or leaks in cracked masonry or concrete surfaces.
This product is an alkali resistant, fiberglass reinforced, portland cement based surface bonding cement used for construction of dry-stack (without mortar) cement block walls. It is good for waterproofing and strengthening block walls without mortar, and rehabilitating existing walls with a water-resistant and decorative coating. We stock both white and gray.
This product is a pourable cement that develops strength greater than concrete; just add water. It expands as it hardens and sets in 10-30 minutes. Ideal for setting bolts, handrails, or anything metal to be anchored in concrete. Good for both interior and exterior applications.
This product is a dry mixture of portland cement, waterproofing agents and sand used to seal and beautify concrete, block, brick, stucco, and stone walls. It can be used in both interior and exterior applications both above grade and below. It is available in both white and gray.
This product is a high strength, non-metallic grout designed for precision grouting and general construction applications. Add only water to obtain a plastic, flowable or fluid consistency. Non-shrink characteristics make it stable and capable of handling high load transfers. Use for grouting heavy equipment, pre-cast concrete, bearing plates, steel columns or anchoring applications.
This product is a rapid hardening, high strength, non-shrink blend of gypsum cement and graded sand designed to level concrete and wood floors. It can be trowel applied to interior concrete and wood floors prior to the installation of ceramic tile, resilient flooring, carpet and other floor coverings.
Vinyl Concrete Patcher is a multi-purpose concrete repair material with strong adhesive properties; just add water. Trowels to a feather edge of 1/16″ (1.6 mm). Made of a special blend of exterior grade vinyl resin, fine sand, and portland cement.
This product is a dual purpose water based clear acrylic coating that cures freshly placed concrete and seals concrete and masonry surfaces. The sealer can be applied immediately after the finishing application and provides a durable semi-gloss finish. It eliminates the need for water curing freshly placed concrete, and it protects and seals from acids,… Read more »
We stock concrete stretcher block in 4, 6, 8, and 10 widths. 4 inch (3⅝ by 7⅝ by 15⅝) 6 inch (5⅝ by 7⅝ by 15⅝) 8 inch (7⅝ by 7⅝ by 15⅝) 10 inch (9⅝ by 7⅝ by 15⅝)
We stock cement solid block in 2, 4, 6, and 8 inch widths. 2 inch (1⅝ by 7⅝ by 15⅝) 4 inch (3⅝ by 7⅝ by 15⅝) 6 inch (5⅝ by 7⅝ by 15⅝) 8 inch (8⅝ by 7⅝ by 15⅝)
Steel Wire Mesh Sheets for concrete reinforcement is stocked in 5′ X 10′ sheets and in both 6 and 10 gauge strength.
Steel Wire Mesh Rolls for concrete reinforcement is stocked in 5′ X 250′ rolls in 10 gauge strength.
Steel Rebar for strengthening concrete comes in 20 foot lengths and is stocked in 3/8″, 1/2″, 5/8″, and 3/4″ thicknesses. It can be cut to custom length for an additional charge.
We stock 4″ by 10′ PVC Perforated Sewer & Drain Pipe and fittings (not pictured).
We stock 4″ by 10′ PVC Solid Sewer & Drain Pipe and fittings (not pictured).
We stock 100ft perforated rolls in 2′, 3′, 4′ and 6′. The 4″ perforated is available in a 250ft roll, or in a 100ft roll with sock. We also stock 4″ solid (non-perforated) rolls in100ft and 250ft lengths.
This is a woven slit film polypropylene geotextile that provides separation for good subgrades by preventing mixing of subgrade soils and base aggregates. High grab tensile and puncture strengths provide good performance in a wide range of roadway applications. This product is available in 12.5′ by 432′ rolls, and 17.5′ by 309′ rolls, and can… Read more »
This product is a nonwoven geotextile fabric composed of stable polypropylene fibers used for soil separation and drainage. This product combines high water flow rates and durability while providing excellent soil retention and is used in a wide variety of applications including subsurface drainage and roadway separation applications. This product is available in 15′ by 300… Read more »
An all-purpose, granular clay absorbent that quickly cleans up water, oil, grease and other liquid spills.
This premium, all weather, permanent pot hole repair material is used by all the public agencies in Western New York for road and street maintenance and is the ideal solution for potholes, utility cuts and other repair applications. The product works in all conditions – including cold and wet applications*. There is no tacking or… Read more »
FBC Fast Dry Asphalt Paint is a solvent-based quick dry primer or general purpose black asphalt paint. Apply by brush, medium nap roller or airless spray equipment. Coverage will vary from 3/4 to 1 gallon per 100 square feet depending on porosity and type of surface being coated.
Silt Fence is a temporary sediment control device used on construction sites to protect water quality in nearby streams, rivers, lakes from sediment in storm water runoff. This product is 3′ in height and comes in 100′ rolls. We stock both with fiber mesh (not pictured) and without (pictured).
Black Beauty is a 99% silica free recycled sand blasting media. We stock both the 20/40 Fine Grit and the 12/40 Medium Grit.
Calcium Chloride Flakes are a highly effective ice melt agent at temperatures down to -25 degrees. This product is also effective as a dust control agent as it draws and holds moisture.
Calcium Chloride Pellets are a highly effective ice melt agent at temperatures down to -25 degrees. This product is also effective as a dust control agent as it draws and holds moisture.
Our store at 191 Broadway Road in Gowanda is stocked with paint, tools, pipe, block, bagged cement, rebar, wire mesh, and many other supplies common to contractor needs. Our summer hours are 7:00 AM to 4:30 PM weekdays. To reach the store directly call 716-532-2723.
This single axle can carry up to 8 tons and is ideal for making home deliveries. It is more maneuverable than a Triaxle because of its short wheel base.
Tractor Trailer Dumps can carry 35 tons and are ideal for conveying materials to construction sites and material suppliers. Tractor Trailer Dumps need a large flat area to dump their load.
This small single Axle is based at our Collins plant and is ideal for home deliveries and hard-to-get-to spots. It can carry up to 4 tons.
A Triaxle is a full sized dump truck capable of delivering about 22 tons. Triaxles can make home deliveries as well as supplying materials to contractors.
Top soil is the extremely important upper layer of dirt in your garden, farm, or lawn. These few inches of dirt contain all the necessary nutrients, bacteria, and loose organic matter needed to create healthy and flourishing growing environments. Unscreened Top Soil is delivered out of our stock piles as is. It is variable depending… Read more »
Top soil is the extremely important upper layer of dirt in your garden, farm, or lawn. These few inches of dirt contain all the necessary nutrients, bacteria, and loose organic matter needed to create healthy and flourishing growing environments. For many projects, a simple unfiltered and unscreened top soil will be everything you need to… Read more »
We produce a wide range of hot mixed asphalt products from four plants in five locations. We cater to small contractors doing private jobs and large heavy highway contractors doing NYSDOT contract work. We have knowledgeable and experienced professionals in our sales department who would be glad to discuss your project with you. E-mail us… Read more »
This premium, all weather, permanent pot hole repair material is used by all the public agencies in Western New York for road and street maintenance and is the ideal solution for potholes, utility cuts and other repair applications. The product works in all conditions – including cold and wet applications. There is not tacking or… Read more »
This fine sand resembles Mason Sand but has occasional pebbles and roots in it. It works well for play sand or on volleyball courts. It is commonly used by dairy farmers as bedding for cows.
Mason Sand is a fine clean sand used for brick and block mortar. Mason Sand makes a good Pool Sand for under pool liners. This sand is what we usually recommend for sand boxes, beaches, and volleyball courts.
Very coarse clean sand used in both residential and commercial septic systems for filtering waste water.
Coarse Washed Sand typically used for mixing with cement and coarse aggregates to make concrete.
White Silica Sand for golf course traps. Good for mixing with white cement for white mortar. Not recommended for sand box play sand.
Asphalt Sand is a coarse washed sand used primarily in the production of Asphalt Mixes. This sand is the result of crushing and is typically the most angular of sands available. Because it compacts it works well as a leveling course under pavers or flagstones. It is a good abrasive sand that works well for… Read more »
Abrasive sand is coarse washed sand that works well for aiding in traction on snow and ice covered roads. At our Springville plant we machine blend it with salt at a range of ratios from 50%/50% to 90%/10% for winter maintenance customers. We have the option of adding magnesium sulfate to our blends to increase… Read more »
Oversize is generated in the process of screening Bank Run Gravel. It is not a washed product, so oversize piles tend to have some Bank Run Gravel mixed in. Oversize is sorted into size ranges of 2 to 3 inches, 2 to 6 inches, 4 to 12 inches, 8 to 18 inches, 18 to 36… Read more »
This product is the unprocessed millings from road building projects. Its top size is variable, but mostly 4 inch minus with lots of fines mixed in. This product is good for heavy duty parking lots and driveways. When properly applied and compacted it can result in a rut and pot hole resistant surface.
Bank Run Gravel is unprocessed gravel. Depending on the source, it can be 4″ minus, meeting NYSDOT Item 203 requirements for Select Fill, or a very coarse, clean, compactable fill with 8″ and larger stones in it. It is usually the least expensive base or compactable fill available.
Minus 2″ Screened Gravel is produced by processing Bank Run Gravel through a 2″ screen. The resulting material is a 2″ and minus compactable subbase. This product varies in consistency depending upon the source. The 2″ Screened Gravels we produce at all of our various sources meet NYSDOT 304 Type 4 requirements for soundness and… Read more »
Minus 2″ Crusher Run Limestone is produced by crushing blasted Limestone and reducing everything to 2 inches and smaller. The resulting material is a highly compactable subbase that is ideal for building and surface treating heavy duty driveways and parking lots. Its gray color is visually distinct. Limestone is not locally produced, so the cost… Read more »
Minus 2″ Crusher Run Hard Head Gravel is made by processing 2″ to 8″ cobbles through a crusher resulting in a 100% crushed subbase that has a range of sized particles from 2 inches down to dust. -2″ Crusher Run Hard Head Gravel is an excellent subbase for roads, driveways, and building pads. It is… Read more »
Minus 2″ Crusher Run Gravel is produced by processing bank run gravel through a crusher and reducing everything to 2 inches and smaller. The resulting compactable material is a blend of natural and crushed product with more coarse aggregate than a typical screened gravel. The angularity of the crushed materials add to the stability of… Read more »
Minus 1″ Crusher Run Limestone is produced by crushing blasted Limestone and reducing everything to 1 inch and smaller. The result is a highly compactable subbase that is ideal for building and resurfacing driveways and parking lots. Its gray color is visually distinct. Crusher Run Limestone is not locally produced, so the cost of importing… Read more »
Minus 1″ Crusher Run Gravel is produced by processing bank run gravel through a crusher and reducing everything to 1 inch and smaller. The resulting material is a blend of natural and crushed product with more coarse aggregate than a typical screened gravel. The angularity of the crushed materials adds to the stability of this… Read more »
Minus 1″ Screened Millings are made by processing milled asphalt from road building projects through a 1 inch screen. The resulting 1 inch and smaller product is ideal for constructing, surfacing and repairing driveways and parking lots. When properly applied and compacted it can be very pothole and rut resistant. We also make -2″ screened… Read more »
This blend of Concrete Sand & Crushed #1 Gravel is used for mixing with cement and water to make concrete.
This very coarse, crushed, gravel with a top size of 4″ is good for building roads over poor or muddy soil conditions. Although the sample pictured is washed, it is often produced by dry screening, which allows for considerable dirt and fines to cling to the finished product.
This primarily 2″ clean, washed, round gravel with a top size of 2-1/2″ is commonly used for roofing ballast. It is also an attaractive ground cover in landscape applications.
This primarily 1″ round, washed, natural gravel with a top size of 1-1/2″ is good for drainage and roofing applications. It works well for drainage around perforated pipe.
This primarily 1/4″ clean, rounded, natural gravel with a top size of 1/2″ works well as drainage material or self compacting fill (when contained in a hole or a foundation). Round #1A is sometimes used for playground cover.
This primarily 1/2″ clean, rounded natural gravel with a top size of 1″ is good for drainage or self compacting fill (when contained within a foundation). They are attractive when washed or cleaned up by the rain and make nice ground cover for landscaping.
This clean, crushed, washed gravel is primarily 1-1/2″ with a top size of 2″ and is commonly used as an ingredient in asphalt base courses. This coarse stone works well for constructing a farm or logging road over reasonably stable soils. It is very difficult to shovel this coarse product by hand.
This very coarse, crushed, washed, clean gravel is primarily 2″ in size with a top size of 2-1/2″. It is good for establishing roads over semi-firm soil conditions or topping extremely muddy drives. This product is too coarse to shovel by hand.
This primarily 1″ crushed, washed gravel with a top size of 1-1/2″ is often used for drainage around perforated pipe, under concrete slabs, and as a coarse driveway topping for soft, very muddy driveways.
This primarily 1/4″ washed, crushed gravel with a top size of 1/2″ is used primarily in asphalt mixes and for oil chipping aggregate. It would work well for a gravel walkway or very fine driveway topping.
This primarily 1/2″ clean, crushed gravel with a top size of 1″ is great for driveway topping and drainage applications. As a driveway topping it works best on firm but slightly muddy drives or parking areas. It works well for drainage around perforated pipe or under concrete slabs. It is commonly used for pipe bedding… Read more »
Ranging in size from 1 1/2″ to 1/4″, this clean, washed, crushed gravel is commonly used as an ingredient in Ready Mixed Concrete. This product works well for drainage media around perforated pipe or as a coarse driveway topping for soft, muddy driveways.